Technical Resources · Metal Buildings

Metal Building Insulation R Value: Materials vs. Roof and Wall Assemblies

A metal building insulation R value describes the resistance of an insulation layer to heat flow, not the performance of a completed roof or wall. Steel purlins, wall girts, fasteners, and insulation compressed at framing connections can increase heat transfer through the assembly.

For example, a reference standing-seam metal roof with thermal blocks and a single R-19 insulation layer has an effective assembly resistance of approximately R-12.2. With an added R-6.5 continuous insulation layer, the corresponding reference assembly reaches approximately R-18.9. The construction details, not the material rating alone, determine the result.

Metal building insulation R value compared with complete roof and wall assembly U-factors
Material R-value and whole metal-building assembly performance must be kept separate.

Three points for a project specification

  • Material valueUse insulation thickness and thermal conductivity to calculate the resistance of the material layer.
  • Assembly valueAccount for framing, insulation compression, connections, and the continuity of the installed system.
  • Specify the systemIdentify the product, thickness, facing, installation arrangement, and required roof or wall performance.

Fiberglass R-Values by Insulation Thickness

For fiberglass used in metal building roofs and walls, a metal building insulation R value starts with the layer’s thickness and thermal conductivity. For a uniform, uncompressed insulation layer, thermal resistance is calculated as:

R = d / λ

Here, d is insulation thickness in meters and λ is thermal conductivity in W/(m·K). The resulting SI R-value is expressed in m²·K/W.

Using a fiberglass blanket conductivity range of 0.035–0.042 W/(m·K), the approximate material R-values at common thicknesses are:

Fiberglass thickness SI R-value (m²·K/W) US R-value (ft²·°F·h/Btu)
25 mm 0.60–0.71 R-3.4 to R-4.1
50 mm 1.19–1.43 R-6.8 to R-8.1
75 mm 1.79–2.14 R-10.1 to R-12.2
100 mm 2.38–2.86 R-13.5 to R-16.2

These are calculated values for the fiberglass layer only. They do not include steel thermal bridges or reductions in installed thickness caused by compression. For instance, at λ = 0.040 W/(m·K), 50 mm of fiberglass provides approximately R-7.1 in US units, while 100 mm provides approximately R-14.2. At constant conductivity, doubling thickness doubles material resistance.

Where a specified metal building insulation R value exceeds what can be accommodated in one layer, the available installation depth, roof or wall construction, and suitability of a multilayer arrangement must be considered.

Why the Same R-Value Performs Differently in Steel Buildings

Steel conducts heat much more readily than fiberglass. In a metal building, purlins, girts, fasteners, and their connections to the cladding can form heat-transfer paths around or through the insulation.

At roof purlins, a blanket may be compressed between the framing and roof panels. Its reduced thickness at those points lowers local thermal resistance, even while insulation between purlins remains at full depth. Wall girts and cladding connections can create similar interruptions in walls.

Thermal blocks, appropriately designed two-layer arrangements, continuous insulation, and liner systems can reduce these effects. Their effectiveness depends on where the layers sit, how they meet the steel framing, and whether their continuity is maintained across the assembly. A nominal metal building insulation R value therefore cannot establish roof or wall performance without the installation details.

Metal Building Insulation R Value vs. Assembly U-Factor

The U-factor describes heat transfer through the complete roof or wall assembly for a given temperature difference. A lower U-factor means better overall thermal performance. The reference constructions below illustrate why an insulation product rating and an installed assembly rating must be distinguished.

Reference assembly Insulation configuration Overall U-factor (US units) Equivalent assembly R-value (US units)
Standing-seam metal roof with thermal blocks Single R-19 layer 0.082 R-12.2
Same type of metal roof R-19 plus R-6.5 continuous insulation 0.053 R-18.9
Metal wall with a compressed single layer R-19 0.147 R-6.8
Same type of metal wall R-19 plus R-6.5 continuous insulation 0.075 R-13.3

U-factors are in Btu/(h·ft²·°F). Equivalent assembly R-values are calculated as 1/U. These values apply to specific reference constructions, including their framing and installation details; they are not universal ratings for all metal buildings.

The same nominal R-19 insulation produces different overall results in the illustrated roof and wall because the framing and installation details differ. In the roof example, adding R-6.5 continuous insulation reduces the U-factor from 0.082 to 0.053, approximately 35% less heat transfer for the same temperature difference.

This comparison shows why a higher blanket rating alone does not guarantee a corresponding improvement in assembly performance. For a project specified by U-factor, the complete construction must be evaluated rather than relying only on the metal building insulation R value.

Metal Building Insulation R Value: R-13, R-19, or R-30?

There is no single material R-value suitable for every metal roof or wall. The appropriate requirement depends on the climate zone, building use, indoor temperature needs, roof or wall construction, and applicable energy code. Specifications may refer to R-13, R-19, R-25, or R-30, but the requirement must be identified as either a material value or an assembly performance target.

At a fiberglass thermal conductivity of 0.035–0.042 W/(m·K), the approximate uncompressed thicknesses needed to achieve the following material-only US R-values are:

  • R-13: approximately 80–96 mm.
  • R-19: approximately 118–141 mm.
  • R-30: approximately 185–222 mm.

These calculations describe material resistance, not the effective R-value of an installed metal roof or wall. They also should not be treated as a list of standard single-roll thicknesses; the product range and possible multilayer configuration must be reviewed separately.

Where a project instead specifies a maximum assembly U-factor, compare the proposed construction with that limit. For example, with a hypothetical roof requirement of U ≤ 0.060 Btu/(h·ft²·°F), the single R-19 reference roof above (U = 0.082) would not meet the target, whereas the reference roof with an added R-6.5 continuous layer (U = 0.053) would.

For existing buildings, available space, existing insulation, and roof connections may constrain the installation. In new construction, purlin or girt spacing, insulation layers, thermal breaks, and liner systems can be coordinated earlier. In either case, check compression, layer continuity, installation depth, and condensation risk when translating a metal building insulation R value into a practical specification.

Choosing Insulation Products for Metal Buildings

Once the target metal building insulation R value and any required assembly U-factor are clear, select a product form that suits the roof or wall construction. Insulvora supplies fiberglass insulation rolls, foil-faced fiberglass rolls, and fiberglass boards for appropriate metal-building applications.

Fiberglass Insulation Rolls for Large Roof and Wall Areas

Fiberglass Insulation Roll is suited to broad roof and wall areas in steel-framed buildings. Available product ranges include 25–100 mm thickness, 10–72 kg/m³ density, a typical 1.2 m width, and 5–30 m roll lengths.

A higher material R-value may require suitable insulation thickness or multiple layers. The design must account for available space and any compression or thermal bridges where blankets meet the framing. The nominal metal building insulation R value should not be substituted for the installed assembly U-factor.

Foil-Faced Fiberglass for Assemblies Requiring a Facing

Foil-Faced Fiberglass Insulation Roll is available with single-sided, double-sided, and reinforced foil-facing options. The underlying fiberglass layer is available in 25–100 mm thicknesses.

Depending on the facing construction, the foil can provide surface coverage or serve a vapor-control function. Its position, joint sealing, and continuity need to be coordinated with the building envelope. For a foil-faced product, the metal building insulation R value must be based on the fiberglass layer, not an assumed contribution from reflectivity. A foil facing does not eliminate thermal bridges through steel.

Fiberglass Boards for Suitable Wall and Liner Constructions

Fiberglass Insulation Board can be considered for wall liners, framed cavities, and locations requiring board-form insulation. Thickness and density are selected according to the wall layout and installation method.

Where boards are used in a continuous insulation arrangement, the supports, fixings, joints, and required assembly performance also matter. Product form should be selected for the construction details, not for the stated metal building insulation R value alone.

For wider material and assembly options, see Metal Building Insulation. For installation details involving purlins, girts, joints, and layer continuity, see Metal Building Insulation Installation. For general material resistance comparisons, see Fiberglass R-Value.

Request Metal Building Insulation Materials and Pricing

Insulvora supplies fiberglass rolls, foil-faced fiberglass, and related board products for metal building roofs and walls. Share your required metal building insulation R value or assembly U-factor target, roof or wall arrangement, desired product form, thickness, facing, and installation constraints where available. We can discuss suitable product options, available specifications, and pricing; project-specific assembly performance must be checked against the intended construction.